4 Ways to Fix Android Blue Screen of Death On Tecno Spark 10 4G

Android is undoubtedly amongst the best smartphone platforms but comes with its own share of glitches. The Android screen of death is observed by many users all over the world who complain of their device screen turning blue rendering their phone/tablet unresponsive. This is called the Android blue screen of death and it usually occurs when you turn on your device by pressing the Power On button but your device does not boot up normally and remains stuck at a plain blue screen without any error message.

Such an Android screen of death is caused by a temporary software crash but can also occur due to certain hardware issues. We understand the inconvenience caused to you when you see the Android blue screen of death. Here are ways to fix the error and great software to extract all your data to keep it unaltered and safe.

Read on to learn more about the Android screen of death and ways to combat it.

Part 1: How to rescue data on Tecno Spark 10 4G with blue screen of death?

The Android blue screen of death issue is not a difficult problem to deal with and can be fixed by you by following the easy steps given in this article. We suggest that all readers rescue the data stored on their Android devices to prevent data loss and keep it stored in your PC from where it can be accessed and recovered by you anytime, anywhere. This task might sound tedious, but, we have for you Dr.Fone - Data Recovery (Android) , a software specially designed to retrieve data from broken and damaged Tecno Spark 10 4G phones and tabs, especially Tecno Spark 10 4G devices, and keep it safe in your PC without tampering with it or altering its format. It efficiently extracts data from broken or unresponsive Tecno Spark 10 4G devices, phones/tabs stuck at black/blue screen, or whose system crashed due to a virus attack.

Dr.Fone - Data Recovery (Android)

World’s 1st data retrieval software for broken Android devices.

• It can also be used to recover data from broken devices or devices that are damaged in any other way such as those stuck in a reboot loop.
• Highest retrieval rate in the industry.
• Recover photos, videos, contacts, messages, call logs, and more.
• Compatible with Tecno Spark 10 4G devices.

3,145,271 people have downloaded it

Follow the steps given below to extract data when you experience an Android screen of death:

1. Download, install, and run the Dr.Fone - Data Recovery (Android) tool on your PC. Connect your device using a USB cable and move on to the main screen of the software.

2. Once you launch the software, you will see many tabs before you. Click on “Data Recovery” > “Android”.

3. And then choose “Recover from Broken Phone” from the program’s screen.

4. In this step, choose from the two options before you the true nature of your device as shown in the screenshot below.

5. You will now be asked to feed in your phone’s model type and name as shown in the screenshot below. Give correct details for the software to identify your device smoothly and hit “Next”.

6. In this step, refer to the instructions in your device manual to enter into Download Mode on your Tecno Spark 10 4G and hit “Next”. An example of what to do to reach Download Mode is shown below.

7. Finally, let the software recognize your Tecno Spark 10 4G, and start to download the recovery package for your device.

8. Once it does, you will be able to preview all the files on the screen in front of you before you hit “Recover to Computer”.

The process may take up to a few minutes and once it’s done all your files will be extracted and stored on your PC. You can now move on to troubleshooting the problem without the fear of losing all your important data.

safe & secure

Part 2: One click to fix the Android blue screen of death

We understand how annoying it is to see the Android blue screen of death and fail to access your device data. But, with Dr.Fone - System Repair (Android) , your troubles would burst away.

This software effectively fixes Android screen of death issue along with app crashing, bricked or unresponsive device, stuck on Tecno Spark 10 4G logo, etc. All Android issues are well taken care of by Dr.Fone - System Repair (Android) with one click.

Dr.Fone - System Repair (Android)

Easy and effective solution to fix the Android blue screen of death！

• Every kind of Android system error and problem is resolved.
• It is the premier Android repair software in the market.
• All the latest Tecno Spark 10 4G devices are supported by this program.
• Android blue screen of death can be fixed with a single click.
• Easy to use and no technical skills are needed to operate it.

4,750,154 people have downloaded it

Note: Backing up your device is significant before you carry out the Android repair process. The process of fixing the Android blue screen of death issue may erase data from your Tecno Spark 10 4G. So backing up your Android seems a viable option.

Phase 1: Connecting your Android after preparing it

Step 1: Installation and running Dr.Fone - System Repair (Android) on your system takes you to the main screen. Choose the ‘System Repair’ option followed by connecting the Android device.

Step 2: Press the ‘Android Repair’ option before tapping the ‘Start’ button.

Step 3: Over the Tecno Spark 10 4G device information window, select all relevant data about your device followed by the ‘Next’ button.

Phase 2: Initiate repairing after entering ‘Download’ mode

Step 1: Get the Tecno Spark 10 4G device in ‘Download’ mode to fix the Android blue screen of death issue. Here is how –

• On a ‘Home’ button-less device – you need to switch off the Tecno Spark 10 4G device. Now, hold the ‘Volume Down’, ‘Power’, and ‘Bixby’ keys together for about 10 seconds and release. Hit the ‘Volume Up’ key to get into ‘Download’ mode.

• On a ‘Home’ button device – shut down the Android phone/tablet, and then push the ‘Power’, ‘Volume Down’, and ‘Home’ keys for 10 seconds. Let go of the keys and press the ‘Volume Up’ key to enter ‘Download’ mode.

Step 2: Tap the ‘Next’ button to download firmware.

Step 3: Dr.Fone - System Repair (Android) would verify the firmware post-download. It will start repairing the Android system automatically.

safe & secure

Part 3: Force Restart Your Tecno Spark 10 4G

A force restart is a basic step that can clear minor software glitches. It has the potential to resolve the Android blue screen of death issue. Force restarting your device can clear temporary bugs and reset all processes. It is a simple yet often overlooked way to fix the Android blue screen of death issue. Use the following steps to force restart your Tecno Spark 10 4G:

Step: On your Tecno Spark 10 4G, press and hold the “Power” and “Volume Down” keys for around 10 seconds. Release the keys when your device reboots and wait for it to complete rebooting.

Part 4: Remove phone battery to fix blue screen of death

The best home remedy to fix any kind of Android screen of death remove the Tecno Spark 10 4G device’s battery. This technique might sound too simple, but it has solved the Android blue screen of death issue for many users whose devices started normally after reinserting the battery. Here is what you should do.

1. Open the back cover of your Tecno Spark 10 4G and carefully remove its battery.

2. Let the battery be out for 5-7 minutes. Meanwhile, long press the power button to drain out any residual charge from your device.

3. Now reinsert the battery and attach the back cover.

4. Turn on your device and see that it boots normally all the way to the Home/Locked Screen without getting stuck at Android blue screen of death.

Note: Not all Android devices allow you to remove their battery. If you own such a device, try the next step as it is your only option to fix the Android blue screen of death problem.

Part 5: Put out your SIM Card/SD card and reinsert

In some cases, issues related to the Android blue screen of death can be caused by problems with the SIM card or SD card. Removing and reinserting these cards can help resolve potential conflicts or glitches. Remember that this method can help resolve issues related to SIM card or SD card conflicts. However, it may not address more complex software or hardware problems causing the blue screen issue.

Part 6: Clean or change the LCD connector

If you’re facing the Android blue screen of death issue, the issue might be related to a hardware problem. The problem can be a loose or damaged LCD connector. In this scenario, you can try cleaning or changing the connector. This method is more advanced and involves disassembling your device. That’s why you need to proceed with caution and only if you’re comfortable with hardware tasks.

Part 7: Update to the latest Android version

Software problems can manifest the Android equivalent of a blue screen of death. It is usually triggered by errors or anomalies within the operating system. To address these concerns, upgrading to the most recent version of the Android OS proves effective. However, updating your device’s software could introduce fresh glitches or compatibility conflicts. These steps outline the process of updating your device to the latest OS:

Step: Open the Settings app on your Tecno Spark 10 4G by locating and launching it. Proceed by scrolling through the options and selecting “Software Update.” In the ensuing screen, choose “Download and Install” to start a search for any available updates.

Part 8: How to fix the Android blue screen of death by factory reset?

The Android screen of death is a very confusing issue as it freezes your device at a blue screen with no options to navigate further. In such a situation you may consider performing a Factory Reset, better known as Hard Reset as you will need to enter Recovery Mode to implement this technique. Although resting your device will wipe off all its data but you don’t need to worry as Dr.Fone toolkit Android Data Extraction software can retrieve all your files and keep them safe.

Accessing Recovery Mode differs for different Android devices. Thus, we suggest that you consult your device manual to understand how to boot into Recovery Mode on your particular Android device and then follow the steps given below:

Once you are on the Recovery Screen, you will see a list of options before you, similar to the screenshot below.

Use the Volume Down button to scroll downwards and reach the “Wipe data/Factory reset” option.

Now use the power button to select it and wait for the Tecno Spark 10 4G device to reboot automatically.

You will notice that the Android device will turn back on without getting stuck at the Android blue screen of death. Now you can set up your device from scratch.

Part 9: What Should You Do if Android Still Stuck on Blue Screen?

Have you tried all the methods, and your Tecno Spark 10 4G is still stuck on the blue screen of death? In this case, it’s important to consider the possibility of a hardware issue. Remember that hardware issues can be complex. Trying to fix things without the right expertise can result in additional harm. If you’re uncertain about the next steps, it’s wisest to ask for assistance from a trained professional.

The Android screen of death, especially the Android blue screen of death, is not a very pleasant sight and could worry you. The good news is that this problem can be fixed by you sitting at home without any technical assistance. Follow the simple and easy tips given above to reboot your device and use the Dr.Fone - Data Recovery (Damaged Device) tool to rescue your data in the most efficient and effective way, then use Dr.Fone - System Repair (Android) to repair your Tecno Spark 10 4G.

safe & secure

8 Workable Fixes to the SIM not provisioned MM#2 Error on Tecno Spark 10 4G

SIM cards are small chips that act as a connecting medium between your cell phone and your carrier. It is programmed to help your carrier identify your cell phone account with certain information. And eventually, you are enabled to make calls and to make use of mobile internet. Now, if your device is showing “SIM not provisioned” on Android then it signifies that the connection to carrier network cannot be established or perhaps, your carrier isn’t able to identify your cell phone account.

Part 1. Why does the error “SIM not provisioned MM#2” pop up?

There can be numerous reasons behind the pop up that reads “SIM not provisioned” on Android. But basically, it most probably affects the users who have registered a new SIM card. If you get to experience this issue in other situations or if the SIM is not working in Android, then the problem is with the SIM card and needs to be replaced. Anyways, here is a list of situations when the “SIM not provisioned” error may bother you.

• You got a new SIM card for your new phone.
• You are transferring your contacts into the new SIM card.
• In case, the carrier network provider’s authorization server is unavailable.
• Perhaps, you’re out of the reach of the carrier coverage area and that too, without active roaming agreement.
• Though new SIM cards work flawlessly. But it is often necessary to get your SIM card activated due to security reasons.

Just in case, you haven’t bought any new SIM card and the one you were using was working fine until now, then the most probable reasons behind it could be listed below:

• If your SIM card is too old, possibly it might have gone dead, try replacing it.
• Perhaps, the SIM card was not properly inserted into the slot or there might be some dirt between the SIM and smartphone pins.

A yet another reason could be that your SIM card got deactivated by your carrier provider as it could have been locked to a particular phone. Now, if you insert such a SIM card to another device or a new device even, you may get to witness a message that reads “SIM not valid”.

2.1 One click to fix the “SIM not provisioned MM#2” error on Android

Without talking any further, let’s straightly get to the first and the easiest way to repair SIM not provisioned issue on Android. For this purpose, we’re glad to introduce Dr.Fone - System Repair (Android) , one of its kind of tool that is capable of repairing almost all sort of Android OS issues in just a matter of few clicks. Whether it is SIM not provisioned on Android or SIM not working in Android or your device stuck in a boot loop or black/white screen of death. The most probable reason for these errors is Android OS corruption. And with Dr.Fone – Repair (Android) you can efficiently and effectively repair your Android OS in a hassle freeway.

Dr.Fone - System Repair (Android)

Android repair tool to fix “SIM not provisioned MM#2” error

• Fix any type of Android system issue with ease.
• Even novice users can use it without any hassle.
• Compatible with all major Tecno Spark 10 4G smartphone models.
• Highest success rate in the market for fixing Android issues.
• Supports all Android OS versions.

3981454 people have downloaded it

Step by step Tutorial to fix “SIM not provisioned MM#2” error

Step 1. Connect your Tecno Spark 10 4G

Download and launch the Dr.Fone toolkit on your computer and then opt for the “System Repair” option from the main interface. Meanwhile, get your Tecno Spark 10 4G connected with the computer using a genuine cable.

Step 2. Opt for Android Repair and key in important information

Now, hit on the “Android Repair” from the 3 options on the left, followed by hitting the “Start” button. From the upcoming screen, you’ll be asked to key in important device-related information, like brand, model, country, and carrier details. Hit “Next” afterward.

Step 3. Boot your device in Download mode

You must put your device in Download mode for better repairing of your Android OS. Simply follow the onscreen guide to boot your Android in DFU mode and hit “Next” thereafter. Once done, the software will automatically start downloading the most compatible and recent firmware for your device.

Step 4. Initiate Repairing

As soon as the download completes, the software verifies the firmware and automatically initiates repairing your Tecno Spark 10 4G. Within a short period, you’ll notice that your Tecno Spark 10 4G has been successfully repaired.

safe & secure

2.2 Ensure the SIM card is not dirty or wet

At times, the issue can be as simple as cleaning your SIM card and SIM slot properly. Ensuring that SIM is not wet either and then putting it back into its place. If this works, then the SIM not working in Android was due to the dirt or moisture that was preventing proper contact between SIM card pins and smartphone circuit.

2.3 Insert the SIM card correctly

If your SIM card was working properly until yet, there is a good possibility that the SIM card may have moved a bit from its actual location. Eventually, there is poor contact between the SIM card pins and the circuit. Try inserting your SIM card properly with the following steps.

• Power off your Tecno Spark 10 4G and with the help of Q pin, eject the SIM card holder from the SIM slot of your device.
• Now, grab a soft rubber pencil eraser and gently rub it in on the gold pins of SIM card to clean them properly. Then, with the help of a soft cloth wipe away the rubber residue from the SIM card.
• Next, push the SIM back into the SIM card holder properly and push it back into the SIM slot now.
• Turn your device back on and look if your SIM not provisioned on the Android issue is resolved or not.

2.4 Activate the SIM card

Usually, when you buy a new SIM card, it gets automatically activated within 24 hours of being plugged into a new device. But if that’s not happening in your case and you’re wondering how to activate SIM card, make use of the three options below to enable activation:

• Call your carrier service provider
• Send an SMS
• Log on to your carrier’s website and look for the activation page over it.

Note: The aforementioned options are straightforward and are quick ways to enable activation. It depends on your carrier network whether they support them.

2.5 Contact your carrier

Even if your SIM isn’t activated, grab another working device to make a phone call to your carrier or network. Ensure, to explain the entire situation and the error message to them. Be patient while they investigate the issue. It may eat up a heck load of time or may get resolved in a few minutes that completely depend upon the complexity of the issue.

2.6 Try the other SIM card slot

A yet another reason why SIM not working in Android can be because of the SIM card slot might have gone corrupted. Thanks to the dual SIM technology, you do not have to rush immediately to get it to check or repair. You can simply rule out this possibility by ejecting the SIM card from its original SIM slot and then replacing it into the other SIM card slot. If this solution did work out for you then it is obvious that the problem was with the SIM card slot that got corrupted. And hence, it was triggering SIM not responding issue.

2.7 Try the SIM card in other phones

Or just in case, you’ve still no joy and the SIM not provisioned on Android message is bothering you. Try making use of another Android device. Eject the SIM card from the Tecno Spark 10 4G device which is creating problems and try plugging it into other Tecno Spark 10 4G] and other smartphones. Perhaps, this will let you know whether the issue is with your device only or with the SIM card itself.

2.8 Try a new SIM card

Still, wondering how to fix SIM not provisioned? Perhaps, nothing worked for you, right? Well, on that note, you must head to your carrier store and request a new SIM card. Also, inform them about the “SIM not provisioned MM2” error, they will be able to execute proper diagnostics over your old SIM card and hopefully get it resolved. Or else, they’ll equip you with a brand new SIM card and swap the new SIM card into your device and get it activated in the meantime. Eventually, restoring the normal functioning of your device.

Conclusion

In wrapping up, SIM not provisioned errors on Android can be troubling, but they’re certainly fixable. There are several methods, from a simple device restart to reaching out to your network provider. But if these don’t work, we suggest trying Dr.Fone - System Repair (Android) . This tool is known for its ability to handle an array of Android issues and could be just what your device needs. Navigate your tech challenges with ease using Dr.Fone.

safe & secure

Fix the Error of Unfortunately the Process.com.android.phone Has Stopped on Tecno Spark 10 4G

Nowadays, smartphones are integral to life. They serve as your communication lifeline and powerful personal assistant. However, it can be frustrating when a sudden error disrupts our phone’s functionality. One common error Android users encounter is the “Unfortunately, The process.com.android.phone has stopped” error. Fear not if you have come across this error message on your Tecno Spark 10 4G.

This beginner’s guide is here to help you understand the causes of this problem. It will also provide you with practical “unfortunately the phone has stopped solutions.”

Part 1: Learn Why Unfortunately the process.com.android.phone Has Stopped

The error message “Unfortunately, the process com.android.phone has stopped“ typically appears on Android devices when there is an issue with the Phone app. Issues with underlying processes responsible for handling phone-related functions are also a cause.

It can prevent you from making or receiving phone calls, accessing contacts, or using other phone-related features. Following are some of the possible reasons why you may encounter this error:

App or System Update

When you update your device’s OS or the Phone app itself, it is possible to encounter bugs or compatibility issues. These issues can lead to the Phone app crashing and displaying this error message. Sometimes, the updated software may not work with the existing configurations of the Phone app. It results in instability which causes this error.

App Cache/Data Corruption

The Phone app relies on cached data and stored settings to function properly. If the cache or data of the app becomes corrupted, it can cause the Phone app to malfunction. The reasons include interrupted app installations or updates, improper shutdowns, or software conflicts. As a result, you may see the error message indicating that the process com.android.phone has stopped.

Insufficient System Resources

Android devices need sufficient memory (RAM) and processing power to run apps smoothly. If your device is running low on memory or processing capacity, it may struggle to handle the Phone app and its processes. It can lead to crashes and the error message. Running many resource-intensive apps at the same time also causes this issue. Other reasons include too many background processes that contribute to this error.

Conflicting Third-Party Apps

Third-party apps installed on your device can sometimes conflict with the Phone app. These conflicts can occur for various reasons, such as incompatible app versions. The software bugs within the third-party apps or configurations can also clash with the Phone app. Such conflicts can disrupt the normal operation of the Phone app. The result of all this trigger the error message.

Software or Firmware Glitches

Software glitches or firmware issues can occasionally occur in Android devices. These glitches can affect the functioning of system processes, including the Phone app. They may arise from programming errors and system inconsistencies. Sometimes unexpected interactions between different OS components can also lead to this error.

Part 2: 100% Working Fixes To Fix Unfortunately the process.com.android.phone Has Stopped

Having been denied access to your Phone can cause a lot of issues. Luckily, many simple fixes to the “process.com.android.phone has stopped“ error exist. These solutions have worked for many users, and by following them, you may be able to resolve the issue too. Given below are the top 8 fixes to resolve this error and restore your device’s phone functions:

Fix 1: Restart/Reboot your Android Device

One of the simplest yet effective solutions to tackle the “Unfortunately, the process com.android.phone has stopped“ error is to reboot your Tecno Spark 10 4G. Restarting your device can often resolve temporary software glitches or conflicts. This fix requires no technical expertise.

So, it is worth trying before moving on to more complex solutions. Follow the guide below to restart your Tecno Spark 10 4G and potentially fix the error:

• Step: Long-press your Tecno Spark 10 4G’s “Side” key and wait for the power menu to appear. Here, select “Restart” to initiate the reboot of your phone.

Fix 2: Re-insert the SIM Card

There is also a chance that the reason you are seeing this error message relates to the SIM card. A loose or improperly inserted SIM card can cause disruptions in the phone’s communication functions. As a result, you see the “Unfortunately, the process com.android.phone has stopped“ error.

To fix this error, you can remove the SIM card and then re-insert it. If the issue is actually related to a SIM card, the issue will get resolved after you resolve the problem.

Fix 3: Clear the Cache and Data of the Phone App

The “Unfortunately, the process com.android.phone has stopped“ error is connected to the Phone app. In this situation, clearing the cache and data of the Phone app itself can often resolve the issue. This fix focuses on removing any corrupted or conflicting data within the app.

Once the corrupted data is gone, it will restore the Phone app to proper functioning. Here is how to clear the cache and data of the Phone app on an Android device:

• Step 1: Find the Phone app on your Tecno Spark 10 4G and long-press its icon. A small menu will pop up where you need to select “App Info.”

• Step 2: It will lead you to detailed information about the Phone app. Here, press “Storage,” and following that, you will see the “Clear Cache” and “Clear Data” options. Use them in the same order to clear the cache and data of the Phone app.

Fix 4: Disable Automatic Updates Feature

In some cases, this error may occur due to conflicts or compatibility issues with the automatic app updates feature. The automatic update on your Tecno Spark 10 4G keeps your apps updated. Disabling this feature temporarily can help resolve the problem.

As a result, you will be able to use the Phone app without interruptions. To disable the automatic updates option on the Google Play Store, you can use the following steps:

• Step 1: Navigate to the Google Play Store app on your Tecno Spark 10 4G and launch it. Next, tap on the profile icon in the screen’s top right corner. From the options presented, select “Settings.”

• Step 2: In Settings, press “Network Preferences” to expand the option. Now, open the “Auto-update apps” settings and enable the “Don’t auto-update apps” option.

Fix 5: Clear All Apps Cache and Data

When dealing with this error, clearing the cache and data of all apps on your Tecno Spark 10 4G can also help. Doing this will remove any corrupt or conflicting data that might be causing the issue. This fix targets the overall app ecosystem on your device.

It intends to ensure a clean slate and potentially resolve the error. Use the following guide to clear the cache and data of all apps:

• Step 1: Access your Tecno Spark 10 4G’s Settings and tap the “Apps” option. It will lead you to all the apps running on your phone. Here, select an app to see detailed app info.

• Step 2: On the app info screen, scroll down and press “Storage.” Now use “Clear Cache” to clean the app’s cache and “Clear Data” to erase the app’s data. Repeat the same process for all the apps installed on your device.

Fix 6: Clear SIM Toolkit Cache and Data

It is worth considering the SIM Toolkit is a potential source of the problem. The SIM Toolkit is an app that provides functionality related to your SIM card. Its functions include accessing value-added services and managing mobile network settings. Clearing the cache and data of the SIM Toolkit app can help resolve this issue. The steps you need to clear the cache and data of this app are the following:

• Step 1: On your Tecno Spark 10 4G, find the SIM Toolkit app. After finding it, press and hold its icon until a short menu appears. Choose “App Info” from the available options to access its settings.

• Step 2: Now, you need to tap “Storage” to proceed. On the next screen, first, tap “Clear Cache” to clean the cache, and later press “Clear Data.”

Fix 7: Perform Factory Reset

If all previous fixes have been unsuccessful, performing a factory reset is also an option to resolve this issue. It is a drastic measure that can potentially address underlying software issues. However, it’s important to note that a factory reset will erase the entire data and settings of your device.

So, it’s crucial to back up your important files before proceeding with this fix. By doing so, you can restore your device to its original state and eliminate the error. Use the detailed guide described below to factory reset your Tecno Spark 10 4G:

• Step 1: Start by launching the Settings app and selecting “General Management.” Here, choose “Reset,” and following that on the next screen, tap “Factory data reset.”

• Step 2: After tapping “Factory data reset,” hit the “Reset” option. Next, enter your Tecno Spark 10 4G PIN to confirm the process, and use “Delete All” to start the factory reset process.

Fix 8: Try Wondershare Dr.Fone - The Best and Most Reliable Android System Repair Tool

It must be a frustrating experience to try one solution after the next and not be able to resolve the issue. In such situations, the best thing you can do is find a tool that can resolve all Android system problems. While there are many options available online, not all are great. The best Android system repair tool currently available is Wondershare Dr.Fone.

Using Wondershare Dr.Fone, you can fix issues like “Unfortunately, the process.com.android.phone has stopped,” Play Store not working, frozen phone, and many more. It is a specialized tool for resolving Android system issues in Tecno Spark 10 4G devices with support for all modern Tecno Spark 10 4G phones.

Key Features of Wondershare Dr.Fone

• You do not need any technical skills to fix your Android system issues when using Dr.Fone.
• It has the highest success rate in fixing complex software issues related to Android OS.
• Wondershare Dr.Fone supports over 1000 Android models for system repair and can fix most issues within minutes.

Steps To Fix the process.com.android.phone Has Stopped via Wondershare Dr.Fone

All you need to fix your Tecno Spark 10 4G’s system issues is a computer with Wondershare Dr.Fone installed and your device connected to it. Here is the simplified process of resolving most Android system issues in a matter of minutes:

• Step 1: Link Your Android Device with Wondershare Dr.Fone

To start, connect your Tecno Spark 10 4G to your computer. Launch Wondershare Dr.Fone on your computer screen and click on “Toolbox,” located in the left sidebar. From the options available, select “System Repair” and follow it by clicking “Android” on the next screen.

• Step 2: Enter the Required Details of Your Tecno Spark 10 4G

Click on “Start” to initiate the process, and following that, you will be prompted to provide specific details about your Tecno Spark 10 4G. These details include the “Brand,” “Name,” “Model,” “Country,” and “Carrier.” Afterward, tick the box that says, “I agree with the warning, and I am ready to proceed,” and click “Next.”

• Step 3: Resolve The process.com.android.phone Has Stopped Issue

The subsequent step involves entering Download Mode on your device, following the on-screen instructions provided by the software. Once your device is in Download Mode, this Android repair toolkit will proceed to download and install the relevant firmware. Now, select “Fix Now” and confirm the repair of your Tecno Spark 10 4G by entering the code “000000.”

safe & secure

3,595,007 people have downloaded it

Conclusion

To sum the article up, encountering the frustrating error message “Unfortunately, the process com.android.phone has stopped“ can be daunting. However, with the right knowledge and tools, resolving this issue becomes achievable. Throughout this guide, we have explored various troubleshooting methods. These included clearing the cache, rebooting the Tecno Spark 10 4G device, and even performing a factory reset.

While there are many options to fix this error, only one is an excellent choice: Wondershare Dr.Fone. With its powerful Android system repair feature, Wondershare Dr.Fone is a reliable solution to resolve this error.

Also read: