How to Fix the Soft Bricked Tecno Phantom V Fold?

Bricked phone is a serious problem, as your brick smartphone could be suffering from a soft brick or hard brick problem, and must be dealt with carefully. It is very common to see a brick smartphone these days. If you are wondering what exactly is a bricked phone, here is your answer.

A bricked phone, hard brick or soft brick, is a smartphone which refuses to start or boot all the way up the home/main screen of the Tecno Phantom V Fold device. This issue is observed within most Android phones because users have a tendency to tamper with the Tecno Phantom V Fold device settings, flashing new and customized ROMs and tweaking with the essential files. Playing around with the phone’s internal set-up leads to such errors, worst of them being a brick smartphone. Usually, a bricked phone does not switch on and stays frozen at the Tecno Phantom V Fold device logo, a blank screen or even worse, doesn’t respond to any command, even the power on command.

If you are confused about the soft brick and hard brick problems and looking for solutions to fix your priced phone, then here is all you need to know.

Read on to find out more.

Part 1: What is the difference between soft brick and hard brick?

To begin with, let us understand the basic difference between a soft brick and hard brick issue. Both versions of a bricked phone prevent it from booting but differ in their causes and gravity of the problem.

A soft-brick problem is caused merely by a software error/crash and makes your device switch on automatically every time you manually turn it off. This phenomenon is referred to as Boot Loop. Soft bricked Android phones are not as difficult to fix as the hard bricked Android phones. It is convenient to say that a soft bricked phone only boots up half-way and not fully, whereas a hard bricked device does not switch on at all. A hard brick error is thus caused when the kernel, which is nothing but an interface for the software to communicate with the hardware, is tampered with. A hard bricked phone is not recognized by your PC when plugged in and is a serious problem. It requires troubleshooting techniques and cannot be easily fixed as the soft brick problem.

Hard bricked phones are a rare sight, but the soft brick is very common. Given below are ways to fix a soft brick Android phone. The techniques listed here are the best and the most efficient ways to get your phone back to its normal working conditions without losing your important data or damaging your device or its software.

Part 2: Stuck at the Boot Loop

This is the first sign of a soft bricked Android phone. Boot Loop is nothing but when your phone does not remain switched off and turns itself on automatically, and freezes at the logo screen or blank screen, every time you manually try to power it off.

Stuck at boot loop problem can be fixed by clearing your Cache partitions. These partitions are nothing but storage locations for your modem, kernels, system files, drivers and built-in Apps data.

It is advisable to clear Cache partitions regularly to keep your phone free from such glitches.

Since the phone refuses to boot, Cache can be cleared from entering into the Recovery Mode. Different Android devices have different ways to put it in recovery mode. Normally pressing the power key and volume down key helps, but you may refer to your phone’s guide for better understanding and then follow the steps given below to clear the cache partition:

Once you are the recovery mode screen, you will see a number of options as shown in the screenshot.

Use the volume down key to scroll down and select ”Wipe cache partition” as shown below.

>

After the process is completed, select “Reboot System” which is the first option in the recovery mode screen.

This method will help you erase all the clogged up and unwanted files. You may loose some App related data, but that is a small price to pay to fix your bricked phone.

If this method does not boot up your brick smartphone and the problem still persists, there are two more things you can try. Read ahead to find out about them.

Part 3: Booting straight into recovery mode

If your bricked phone does not boot up to your Home Screen or Lock screen and instead boots directly into Recovery Mode, there is not much left to do. Booting straight into recovery mode is undoubtedly a soft brick error but it also indicates a possible problem with your current ROM. The only option you have to flash a new ROM to reboot your bricked phone back to its normal functioning.

To flash a new ROM:

Firstly, you must root your phone and unlock the Bootloader. Every phone’s mechanism to unlock the bootloader is different, thus, we suggest to refer to your user manual.

Once the Bootloader is unlocked, take a backup of all your data by selecting “Backup” or “Android” back in recovery mode. The process should not take long and all you need to do is tap “OK” to config backup.

In this step, download a ROM of your choice and store it in your SD Card. Insert the SD Card in your phone to begin the flashing process.

Once at the recovery mode, select “Install Zip from SD Card” from the options.

Scroll down using the volume key and use the power key to select the downloaded ROM.

This might take a few minutes of your time, but once the process is complete, reboot your phone.

Hopefully, your bricked phone will not boot normally and work smoothly.

Part 4: Booting straight into Bootloader

If your bricked phone boots straight into Bootloader, then this a serious issue and must not be taken lightly. Flashing a new ROM or clearing cache partitions are of little help in such a brick smartphone situation. Booting straight into Bootloader is a peculiar soft bricked Android phone feature and can be tackled only by downloading and flashing your original ROM from the manufacturer. In order to do so, a detailed study about your manufacturer’s ROM, ways to download and flash must be carried out. Since different Android phones come with different types of ROMs, it difficult to cover all the aspects about the different types of ROMs.

Brick smartphone problem has become more prominent than phone freezing or hanging issue. Android users are often seen looking for solutions to fix their soft brick and hard brick phones. Android phones are prone to get bricked and thus, it is important for us to know about the three techniques given above. These methods have been tried, tested and recommended by ay affected bricked phone users. Therefore, these tips are reliable and worth a try. So if your phone acts stubborn and refuses to boot normally, examine the problem carefully and adopt one of the solutions given above which best suits your situation.

8 Workable Fixes to the SIM not provisioned MM#2 Error on Tecno Phantom V Fold

SIM cards are small chips that act as a connecting medium between your cell phone and your carrier. It is programmed to help your carrier identify your cell phone account with certain information. And eventually, you are enabled to make calls and to make use of mobile internet. Now, if your device is showing “SIM not provisioned” on Android then it signifies that the connection to carrier network cannot be established or perhaps, your carrier isn’t able to identify your cell phone account.

Part 1. Why does the error “SIM not provisioned MM#2” pop up?

There can be numerous reasons behind the pop up that reads “SIM not provisioned” on Android. But basically, it most probably affects the users who have registered a new SIM card. If you get to experience this issue in other situations or if the SIM is not working in Android, then the problem is with the SIM card and needs to be replaced. Anyways, here is a list of situations when the “SIM not provisioned” error may bother you.

• You got a new SIM card for your new phone.
• You are transferring your contacts into the new SIM card.
• In case, the carrier network provider’s authorization server is unavailable.
• Perhaps, you’re out of the reach of the carrier coverage area and that too, without active roaming agreement.
• Though new SIM cards work flawlessly. But it is often necessary to get your SIM card activated due to security reasons.

Just in case, you haven’t bought any new SIM card and the one you were using was working fine until now, then the most probable reasons behind it could be listed below:

• If your SIM card is too old, possibly it might have gone dead, try replacing it.
• Perhaps, the SIM card was not properly inserted into the slot or there might be some dirt between the SIM and smartphone pins.

A yet another reason could be that your SIM card got deactivated by your carrier provider as it could have been locked to a particular phone. Now, if you insert such a SIM card to another device or a new device even, you may get to witness a message that reads “SIM not valid”.

2.1 One click to fix the “SIM not provisioned MM#2” error on Android

Without talking any further, let’s straightly get to the first and the easiest way to repair SIM not provisioned issue on Android. For this purpose, we’re glad to introduce Dr.Fone - System Repair (Android) , one of its kind of tool that is capable of repairing almost all sort of Android OS issues in just a matter of few clicks. Whether it is SIM not provisioned on Android or SIM not working in Android or your device stuck in a boot loop or black/white screen of death. The most probable reason for these errors is Android OS corruption. And with Dr.Fone – Repair (Android) you can efficiently and effectively repair your Android OS in a hassle freeway.

Dr.Fone - System Repair (Android)

Android repair tool to fix “SIM not provisioned MM#2” error

• Fix any type of Android system issue with ease.
• Even novice users can use it without any hassle.
• Compatible with all major Tecno Phantom V Fold smartphone models.
• Highest success rate in the market for fixing Android issues.
• Supports all Android OS versions.

3981454 people have downloaded it

Step by step Tutorial to fix “SIM not provisioned MM#2” error

Step 1. Connect your Tecno Phantom V Fold

Download and launch the Dr.Fone toolkit on your computer and then opt for the “System Repair” option from the main interface. Meanwhile, get your Tecno Phantom V Fold connected with the computer using a genuine cable.

Step 2. Opt for Android Repair and key in important information

Now, hit on the “Android Repair” from the 3 options on the left, followed by hitting the “Start” button. From the upcoming screen, you’ll be asked to key in important device-related information, like brand, model, country, and carrier details. Hit “Next” afterward.

Step 3. Boot your device in Download mode

You must put your device in Download mode for better repairing of your Android OS. Simply follow the onscreen guide to boot your Android in DFU mode and hit “Next” thereafter. Once done, the software will automatically start downloading the most compatible and recent firmware for your device.

Step 4. Initiate Repairing

As soon as the download completes, the software verifies the firmware and automatically initiates repairing your Tecno Phantom V Fold. Within a short period, you’ll notice that your Tecno Phantom V Fold has been successfully repaired.

safe & secure

2.2 Ensure the SIM card is not dirty or wet

At times, the issue can be as simple as cleaning your SIM card and SIM slot properly. Ensuring that SIM is not wet either and then putting it back into its place. If this works, then the SIM not working in Android was due to the dirt or moisture that was preventing proper contact between SIM card pins and smartphone circuit.

2.3 Insert the SIM card correctly

If your SIM card was working properly until yet, there is a good possibility that the SIM card may have moved a bit from its actual location. Eventually, there is poor contact between the SIM card pins and the circuit. Try inserting your SIM card properly with the following steps.

• Power off your Tecno Phantom V Fold and with the help of Q pin, eject the SIM card holder from the SIM slot of your device.
• Now, grab a soft rubber pencil eraser and gently rub it in on the gold pins of SIM card to clean them properly. Then, with the help of a soft cloth wipe away the rubber residue from the SIM card.
• Next, push the SIM back into the SIM card holder properly and push it back into the SIM slot now.
• Turn your device back on and look if your SIM not provisioned on the Android issue is resolved or not.

2.4 Activate the SIM card

Usually, when you buy a new SIM card, it gets automatically activated within 24 hours of being plugged into a new device. But if that’s not happening in your case and you’re wondering how to activate SIM card, make use of the three options below to enable activation:

• Call your carrier service provider
• Send an SMS
• Log on to your carrier’s website and look for the activation page over it.

Note: The aforementioned options are straightforward and are quick ways to enable activation. It depends on your carrier network whether they support them.

2.5 Contact your carrier

Even if your SIM isn’t activated, grab another working device to make a phone call to your carrier or network. Ensure, to explain the entire situation and the error message to them. Be patient while they investigate the issue. It may eat up a heck load of time or may get resolved in a few minutes that completely depend upon the complexity of the issue.

2.6 Try the other SIM card slot

A yet another reason why SIM not working in Android can be because of the SIM card slot might have gone corrupted. Thanks to the dual SIM technology, you do not have to rush immediately to get it to check or repair. You can simply rule out this possibility by ejecting the SIM card from its original SIM slot and then replacing it into the other SIM card slot. If this solution did work out for you then it is obvious that the problem was with the SIM card slot that got corrupted. And hence, it was triggering SIM not responding issue.

2.7 Try the SIM card in other phones

Or just in case, you’ve still no joy and the SIM not provisioned on Android message is bothering you. Try making use of another Android device. Eject the SIM card from the Tecno Phantom V Fold device which is creating problems and try plugging it into other Tecno Phantom V Fold] and other smartphones. Perhaps, this will let you know whether the issue is with your device only or with the SIM card itself.

2.8 Try a new SIM card

Still, wondering how to fix SIM not provisioned? Perhaps, nothing worked for you, right? Well, on that note, you must head to your carrier store and request a new SIM card. Also, inform them about the “SIM not provisioned MM2” error, they will be able to execute proper diagnostics over your old SIM card and hopefully get it resolved. Or else, they’ll equip you with a brand new SIM card and swap the new SIM card into your device and get it activated in the meantime. Eventually, restoring the normal functioning of your device.

Conclusion

In wrapping up, SIM not provisioned errors on Android can be troubling, but they’re certainly fixable. There are several methods, from a simple device restart to reaching out to your network provider. But if these don’t work, we suggest trying Dr.Fone - System Repair (Android) . This tool is known for its ability to handle an array of Android issues and could be just what your device needs. Navigate your tech challenges with ease using Dr.Fone.

safe & secure

App Won’t Open on Your Tecno Phantom V Fold? Here Are All Fixes

It is not a very rare phenomenon where an App won’t open, crash abruptly or face trouble while launching on an Android device. Many Android phone users also add to the fact that whenever they try to launch an App, it keeps loading but does not run smoothly, as it should in normal circumstances.

In such a scenario it is obvious for Android Smartphone users to look for possible solutions for such a random error so that their App/Apps load and work normally.

Many people are also interested in knowing about the causes behind why an App won’t open or why multiple/all Apps won’t open. This article will answer your query about why won’t my App open on an Android phone by listing a few probable causes for the problem.

Here are all the fixes you need if an App won’t open on your Tecno Phantom V Fold. Read on to find out all about why Apps won’t open on your Tecno Phantom V Fold and solutions to overcome such a problem.

Part 1: Possible reasons for Apps won’t open

If you are an Android phone user and face a problem while trying to open an App on your device, you will ask yourself “Why won’t my App open?”. To answer your question and explain to you why an App won’t open on your phone, here are some probable and simple reasons to make you understand the real problem.

It is appropriate to tag our generation as smartphone addicts because we use smartphones for anything and everything. All our important information, such as photos, videos, audio files, documents, notes, calendars, emails, etc, are stored on our phones. This causes a major storage/space problem in our phones and a shortage of storage space is one of the main reasons why an App won’t open or why all Apps won’t open on your Tecno Phantom V Fold. To see how much of your storage space is occupied by Apps, go to “Settings” and select “Application Manager”.

Another possible reason for Apps to crash or why an App won’t open is a possible data crash. This may occur due to an unstable internet connection or various other background software interruptions.

The causes for the problem to occur are many and no specific reason can be established as the only reason why Apps won’t open on your Tecno Phantom V Fold. There are a lot of speculations about why such a problem occurs and persists, but it is more important to focus on how to fix if a particular App won’t open or if all Apps won’t open on Android.

Click here

Part 2: Quickest solution to fix apps won’t open on Android

You have already understood ‘why won’t your app open?’ at the start of this article. But, you are not happy with the traditional solutions to fix the app won’t open issue.

Well, in such a case Dr.Fone - System Repair (Android) can prove to be your savior. It resolves failed Android system update issues, crashing apps, and black screen of death. It can also get an unresponsive or bricked Android device or boot loop stuck device fixed with one click.

Dr.Fone - System Repair (Android)

Why won’t my app open? The quick fix is here!

• This is the first software in the industry that repairs Android systems.
• All the latest Tecno Phantom V Fold tablets and mobiles are compatible with it.
• With single-click operation, fixing the app won’t open problems is super easy.
• No technical skills are needed to use the tool.
• The high success rate for Tecno Phantom V Fold Android device issue fixing.

3981454 people have downloaded it

Here comes the detailed guide to fix apps won’t open problem using Dr.Fone - System Repair (Android)

Note: When you are up to fixing apps won’t open issues, make sure to back up your Tecno Phantom V Fold beforehand. These processes might lead to data erasing and you don’t want to suffer data loss this way.

Phase 1: Preparation and connection of Android device

Step 1: Post-installation and launch of Dr.Fone on your computer, you got to press the ‘System Repair’ tab. Connect the Android device later.

Step 2: Hit the ‘Android Repair’ located on the left panel followed by tapping the ‘Start’ button.

Step 3: Feed your Tecno Phantom V Fold details under the Tecno Phantom V Fold device information screen. Please check the warning and press the ‘Next’ button right after that.

Phase 2: Repairing your Tecno Phantom V Fold under ‘Download’ mode

Step 1: You got to boot the Android device under Download mode, as it’s important. The steps for that are as follows –

• Android devise with a ‘Home’ button – Press together ‘Volume Down’, ‘Home’, and ‘Power’ buttons together for 5 to 10 seconds after turning off the Tecno Phantom V Fold device. Release them afterward and click the ‘Volume Up’ button to get into the ‘Download’ mode.

• When there is no ‘Home’ button – Turn off the Tecno Phantom V Fold device and then for 5 to 10 seconds, keep the ‘Volume Down’, ‘Bixby’, and ‘Power’ buttons pressed. Tap the ‘Volume Up’ button after releasing all the buttons to enter the ‘Download’ mode.

Step 2: Hitting the ‘Next’ button starts downloading the Android firmware.

Step 3: Once Dr.Fone - System Repair (Android) verifies the downloaded firmware, it begins fixing the app won’t open the issue asap.

Part 3: 3 Common fixes if a particular App won’t open

In this segment, we will discuss the three best ways to help you fix the problem if only a particular App won’t open/launch/ run and takes an indefinite time to load.

1. Update the App

It is always advisable to keep your Android software as well as your Apps up-to-date and you must constantly check for any updates which may be available in the Google Play Store.

Follow the steps given below to update the app which won’t open on your phone:

• Visit Google Play Store on your Tecno Phantom V Fold.

• Now select “My Apps & Games” from the main menu.

• In this step, you may click on “Update All” to update all Apps for which an update is available or manually select the Apps which you wish to Update.

Once the App is updated, close all Apps and tabs running in the background. Now try to launch the app once again. If it opens, your problem is solved. If not, DO NOT worry as there are more ways to help you.

2. Force Stop the App

Closing the App completely which won’t open on your phone is a good idea. To make sure that no operations are running in the background related to the App, you must “Force Stop” it. Doing this is extremely simple and all you need to do is follow the steps given herein under:

• Visit “Settings” on your phone.

• Click on “Apps” to see a list of all the Apps on your Tecno Phantom V Fold.

• Select the App which won’t open.

• Now click on “Force Stop” as shown below.

3. Clear App Cache and Data

This method resolves the issue to a great extent by wiping off unnecessary App content from your device.

Carefully follow the step-by-step instructions given below to clear all App cache and data:

• Visit “Settings” and select “Apps”.

• From the list of Apps that appears, select the App that won’t open.

• Now tap on “Clear Cache” and “Clear data” directly or under “Storage”.

Part 4: 3 Common fix if all Apps won’t open on Android

In this segment, we will discuss solutions to the problem if all your Apps won’t open. They are simple and easy to follow and solve the error in no time.

1. Android updates

Firstly, it is very important to keep your Android software updated at all times as an old Android version might not support new Apps or updated Apps.

To update your software:

• Visit “Settings” and keep going downwards.

• Now select “About Phone”.

• From the options available on the screen, tap on “System Updates”

• In this step, if you are prompted for an update, follow the instruction given and do so.

Updating your Android software solves most of your problems. This method might sound weird but works wonders when it comes to App related issues.

2. Restart the phone

Restarting your Tecno Phantom V Fold to fix an error might sound old school but it gives good results when your Apps won’t open. Restarting your phone is fairly simple. All you need to do is:

• Long press the power button.

• Now click on “Restart”.

Your phone will automatically restart and once it does, you can try to launch the App. You may also restart your Tecno Phantom V Fold by pressing the power button for about 15-20 seconds.

3. Reset Factory Settings

This method is a little tedious and must be last on your list. Also, make sure you take a backup of all your data and contents stored on your Tecno Phantom V Fold and this solution will completely wipe off your phone making as good as a new smartphone.

To Factory Reset your Tecno Phantom V Fold, carefully follow the guidelines given below:

• Visit “Settings” to find the “Backup and reset” option as shown in the screenshot below.

Click here

• Now click on “Factory Data Reset”>“Reset Device”>“Erase Everything”

Your phone will now reboot and will be required to set up from scratch.

“Why Won’t my App open” is a question asked by many Android phone users who fear that the problem occurs due to a virus attack or a system failure. However, this is not the case. The reason for the error to the surface is quite minor and can be fixed by you, sitting at home, without resorting to any kind of technical or external assistance. The solutions listed above are easy to understand and not very time-consuming.

So go ahead and try them out now!

Also read: